Selecting Silicone Cable Protectors: Hole Diameter, Sheet Thickness, Bend Protection, and Assembly Methods
简要答案：硅胶护线圈用于隔离板材锐边、限制线缆弯折并改善出线口密封。选型应同时核对开孔尺寸、板厚、线径、拉力和 […]
Read the article →Chengxin Silicone Rubber · Engineering and application insights
Silicone Rubber Knowledge
Explore articles on material selection, structural design and sample acceptance to help address your product questions.
Browse by engineering question
Read the technical guidance, or discuss your drawings and operating conditions with us.
Submit Customization Request →
How to Design Silicone Waterproof Plugs and Sealing Caps: Insertion Force, Extraction Force, and Waterproof Rating
Short answer: Silicone waterproof plugs must be both installable and serviceable while providing long-term waterproofing. The key factors include hole diameter tolerance, the interference fit of the sealing ribs, insertion guidance, the removal mechanism, and the material […]
Read the article →
Key Considerations for Custom Silicone Suction Cups: Adhesive Force, Edge Thickness, and Surface Compatibility
简要答案：硅胶吸盘的吸附力由有效面积、真空度、唇边柔顺性和接触表面共同决定。选型不能只看直径，还要验证表面粗糙 […]
Read the article →
Design Guide for Silicone Umbrella Valves: Sealing Surfaces, Preload, and Low-Pressure Opening and Closing
简要答案：硅胶伞阀依靠伞面与阀座贴合实现单向密封。可靠设计需要平衡伞面厚度、阀杆定位、阀座平面度和装配预压，避 […]
Read the article →
How to Choose a Silicone Duckbill Valve? Opening Pressure, Backflow Control, and Service Life Design
Short Answer: The key factors in selecting a silicone duckbill valve are not its physical dimensions, but rather the medium, opening pressure, reverse pressure differential, flow rate, and cycle life. During design, the lip opening should be controlled […]
Read the article →
Storage and Shelf Life of Silicone Seals: Preventing Deformation, Contamination, and Performance Degradation
Even after leaving the factory, silicone parts may still undergo changes in appearance or performance due to temperature, light exposure, compression, and contact with other materials. Proper packaging and first-in, first-out (FIFO) management are key to ensuring assembly quality […]
Read the article →
How to Specify Dimensional Tolerances for Silicone Parts: Shrinkage, Critical Dimensions, and Inspection Methods
硅胶是弹性材料，尺寸结果受收缩、脱模、放置时间和测量方式影响。合理的公差应围绕功能尺寸制定，而非把所有尺寸都设 […]
Read the article →
Causes and Solutions for Sticky Surfaces on Silicone Products: Materials, Curing, and Storage
硅胶件表面发粘会影响手感、装配和外观。排查应覆盖材料迁移、硫化状态、表面处理和储存环境，而不是只依赖擦拭处理。 […]
Read the article →
How to Select the Thickness of a Silicone Sealing Gasket: Compression, Tolerance, and Sealing Surface
硅胶密封垫片的厚度决定初始压缩量和装配容忍度。选择厚度时应从壳体间隙、公差、螺钉预紧和长期回弹整体评估。 1. […]
Read the article →
Design of Silicone Footpads and Shock-Absorbing Pads: Hardness, Friction, and Long-Term Compression
Silicone footpads are commonly used for anti-slip protection, cushioning, and noise reduction in equipment. Their effectiveness is determined by a combination of hardness, contact area, texture, load, and long-term compression. 1. Determine the primary function of the footpad […]
Read the article →